Abstract
This research study proposes the hot-cold tip thermoelectric power (TEP) method to estimate alloying elements segregation and the microstructure variation of high carbon steel cast in a mold. Optical emission spectrometry (OES) showed a higher concentration of carbon, nickel, chromium and aluminum at the ingot center. That elemental saturation produced an increase in perlite content as well as hardness. The nondestructive technique of thermoelectric power was applied varying the hot tip temperature (40, 50, 60, 70°C), where higher temperature values showed to be more sensitive to segregation and microstructural changes. The statistical analysis showed that the thermoelectric power technique is more sensitive to detect the nickel and chromium concentration changes.
REFERENCES
de la Concepción, V.L., Lorusso, H.N., and Svoboda, H.G., Effect of carbon content on microstructure and mechanical properties of dual phase steels, Procedia Mater. Sci., 2015, vol. 8, pp. 1047–1056.
Abbasi, E., Luo, Q., and Owens, D., A comparison of microstructure and mechanical properties of low-alloy-medium-carbon steels after quench-hardening, Mater. Sci. Eng. A, 2018, vol. 725, pp. 65–75.
Turkmen, M., Effect of carbon content on microstructure and mechanical properties of powder metallurgy steels, Powder Metall. Met. Ceram., 2016, vol. 55, nos. 3–4, pp. 164–171.
Mohd Fauzi, M.A., Saud, S.N., Hamzah, E., Mamat, M.F., and Ming, L.J., In vitro microstructure, mechanical properties and corrosion behaviour of low, medium and high carbon steel under different heat treatments, J. Bio-Tribo-Corros., 2019, vol. 5, no. 2.
Guo, D., Hou, Z., Peng, Z., Liu, Q., Chang, Y., and Cao, J., Influence of superheat on macrosegregation in continuously cast steel billet from statistical maximum viewpoint, ISIJ Int., 2021, vol. 61, no. 3, pp. 844–852.
Choudhary, S.K. and Ganguly, S., Morphology and segregation in continuously cast high carbon steel billets, ISIJ Int., 2007, vol. 47, no. 12, pp. 1759–1766.
Wang, W., Bing Hou, Z., Chang, Y., and Hai Cao, J., Effect of superheat on quality of central equiaxed grain zone of continuously cast bearing steel billet based on two-dimensional segregation ratio, J. Iron Steel Res. Int., 2018, vol. 25, no. 1, pp. 9–18.
Krauss, G., Solidification, segregation, and banding in carbon and alloy steels, Metall. Mater. Trans. B Process Metall. Mater. Process. Sci., 2003, vol. 34, no. 6, pp. 781–792.
Flemings, M.C., Our understanding of macrosegregation: Past and present, ISIJ Int., 2000, vol. 40, no. 9, pp. 833–841.
Khan, F.A., The effect of soaking on segregation and primary-carbide dissolution in ingot-cast bearing steel, Metals (Basel), 2018, vol. 8, no. 10.
Lan, P., Tang, H., and Zhang, J., Solidification microstructure, segregation, and shrinkage of Fe–Mn–C twinning-induced plasticity steel by simulation and experiment, Metall. Mater. Trans. A Phys. Metall. Mater. Sci., 2016, vol. 47, no. 6, pp. 2964–2984.
Ennis, B.L., Jimenez-Melero, E., Mostert, R., Santillana, B., and Lee, P.D., The role of aluminium in chemical and phase segregation in a TRIP-assisted dual phase steel, Acta Mater., 2016, vol. 115, pp. 132–142.
Ji, Y., Li, Y., Li, S., Zhang, X., and Zhang, J., Central segregation of high-carbon steel billet and its heredity to the hot-rolled wire rods, TMS Annu. Meet., 2016, pp. 625–633.
Leuschke, U., Puwada, N.R., and Senk, D., Influence of micro-segregation in Pb–S-alloyed free machining steels on the surface quality of the rolled wire-rod, Metall. Ital., 2008, vol. 100, no. 5, pp. 5–11.
Das, S., Mathura, J., Bhattacharyya, T., and Bhattacharyya, S., Metallurgical investigation of different causes of center bursting led to wire breakage during production, Case Stud. Eng. Fail. Anal., 2013, vol. 1, no. 1, pp. 32–36.
Liu, L., Sun, J., and Wang, H., Failure analysis procedure of steel wire drawing fracture, 13th Int. Conf. Fract. 2013 (Beijing, 2013), vol. 2, pp. 1641–1647.
Madhuri, V., Gobinath, R., and Balachandran, G., Effect of carbon on the microstructure and mechanical properties in wire rods used for the manufacture of cold heading quality steels, Trans. Indian Inst. Met., 2019, vol. 72, no. 1, pp. 155–166.
Palit, P., Das, S., and Mathur, J., Metallurgical investigation of wire breakage of tyre bead grade, Case Stud. Eng. Fail. Anal., 2015, vol. 4, pp. 83–87.
ASTM E-381-01, Standard method of macroetch testing steel bars, billets, bloom, and forgings.
Rowe, D. and Bhandari, C., CRC Handbook of Thermoelectrics, 1995.
Lavaire, N., Merlin, J., and Sardoy, V., Study of ageing in strained ultra and extra low, Scr. Mater., 2001, vol. 44, pp. 553–559.
Lavaire, N., Massardier, V., and Merlin, J., Quantitative evaluation of the interstitial content (C and/or N) in solid solution in extra-mild steels by thermoelectric power measurements, Scr. Mater., 2004, vol. 50, no. 1, pp. 131–135.
Soldatov, A.I., Soldatov, A.A., Kostina, M.A., and Kozhemyak, O.A., Experimental studies of thermoelectric characteristics of plastically deformed steels ST3, 08KP, and 12H18N10T, Key Eng. Mater., 2016, vol. 685, pp. 310–314.
Caballero, F.G., Capdevila, C., Alvarez, L.F., and García de Andrés, C., Thermoelectric power studies on a martensitic stainless steel, Scr. Mater., 2004, vol. 50, no. 7, pp. 1061–1066.
Benkirat, D., Merle, P., and Borrelly, R., Effects of precipitation on the thermoelectric power of iron–carbon alloys, Acta Metall., 1988, vol. 36, no. 3, pp. 613–620.
Brahmy, R.B.A., Manganese Enrichment of Cementite and Solubility of Carbon in Low Carbon Steels Investigated by Thermoelectric Power Measurements, 1994.
Perez, M., Massardier, V., and Kleber, X., Thermoelectric power applied to metallurgy: Principle and recent applications, Int. J. Mater. Res., 2009, vol. 100, no. 10, pp. 1461–1465.
MacDonald, D.K.C., Thermoelectricity: An Introduction to Principles, New York: Wiley, 2006.
Kleber, X. and De Lyon, I., Surface and subsurface metallic inclusions detected using hot tip thermoelectric power measurements, ECNDT, 2006, pp. 1–8.
Simonet, L., Kleber, X., Fouquet, F., and Saillet, S., Characterization of segregated areas in ferritic steels by thermoelectric power measurement, Eur. Conf. NDE (2006), pp. 1–9.
Xiao, Y., Li, W., Zhao, H.S., Lu, X.W., and Jin, X.J., Investigation of carbon segregation during low temperature tempering in a medium carbon steel, Mater. Charact., 2016, vol. 117, pp. 84–90.
Carreon, H., Thermoelectric detection of fretting damage in aerospace materials, Russ. J. Nondestr. Test., 2014, vol. 50, pp. 684–692.
Lukhvich, A.A., Sharando, V.I., and Novikov, S.A., Applications of thermoelectric method to studying initial stages of deposition of electrolytic coatings, Russ. J. Nondestr. Test., 2000, vol. 36, pp. 465–470.
Abouellail, A.A., Chang, T., and Soldatov, A.I., Laboratory substantiation of thermoelectric method for monitoring contact resistance, Russ. J. Nondestr. Test., 2022, vol. 58, pp. 1153–1161.
Abouellail, A.A., Chang, J., and Soldatov, A.I., Influence of destabilizing factors on results of thermoelectric testing, Russ. J. Nondestr. Test., 2022, vol. 58, pp. 607–616.
Funding
This work was supported by ongoing institutional funding. No additional grants to carry out or direct this particular research were obtained.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors of this work declare that they have no conflicts of interest.
Rights and permissions
About this article
Cite this article
Hernández, L., Carreón, H. & Bedolla, A. Estimation of the Segregation in a High Carbon Cast Steel by Thermoelectric Power Means. Russ J Nondestruct Test 59, 785–795 (2023). https://doi.org/10.1134/S1061830923600351
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S1061830923600351