Abstract
Using the differential scanning calorimetry method, the influence of the halogen-containing oligomer in the composition of VSK-14-6 adhesive binder on the kinetics of the curing process of prepregs on different fillers was studied and a comparative analysis of the curing kinetics of prepregs based on VSK-14-1 adhesive binder, which does not contain bromine is presented. The calculated kinetic parameters of the curing process of binders in prepregs are presented. The influence of bromine content in the binder composition on the curing process of prepregs is shown.
Similar content being viewed by others
REFERENCES
E. N. Kablov, “What will the future be made of? New generation materials, technologies for their creation and processing are the basis of innovation,” Kryl’ya Rodiny, No. 5, 8–18 (2016).
E. N. Kablov and V. O. Startsev, “Systematic analysis of the influence of climate on the mechanical properties of polymer composite materials based on data of Russian and foreign sources (review),” Aviats. Mater. Tekhnol., No. 2, 47–58 (2018). https://doi.org/10.18577/2071-9140-2018-0-2-47-58
E. N. Kablov, V. O. Startsev, and A. A. Inozemtsev, “Moisture saturation of structural-like elements made of polymer composite materials in open climatic conditions with superimposed thermal cycles,” Aviats. Mater. Tekhnol., No. 2, 56–68 (2017). https://doi.org/10.18577/2071-9140-2017-0-2-56-68
A. P. Petrova and G. V. Malysheva, Adhesive, Adhesive Binder, and Adhesive Prepregs, Ed. by E. N. Kablov (VIAM, Moscow, 2017) [in Russian].
A. I. Starkov, K. E. Kutsevich, T. Yu. Tyumeneva, and A. P. Petrova, “Low-flammability adhesive prepregs intended for the manufacture of integral and three-layer honeycomb structures of aircraft,” Trudy VIAM, No. 5, 04 (2022). https://doi.org/10.18577/2307-6046-2022-0-5-41-52
A. I. Starkov, K. E. Kutsevich, T. Yu. Tyumeneva, “Development of a composite adhesive material based on alternative carbon tow filler brand UMT49S-12K-EP and adhesive binder brand VSK-14-3,” Trudy VIAM, Nos. 6–7, 07 (2020). https://doi.org/10.18577/2307-6046-2020-0-67-62-71
N. V. Antyufeeva, V. M. Aleksashin, and Yu. V. Stolyankov, “Modern methodological support for thermoanalytical studies of polymer composites and prepregs,” Kompozity Nanostrukt. 6, 176–184 (2014).
K. E. Kutsevich, V. M. Aleksashin A. P. Petrova, and N. V. Antyufeeva, “Study of the kinetics of the curing reaction of adhesive binders,” Klei. Germetiki. Tekhnol., No. 11, 27–31 (2014).
V. I. Postnov, S. M. Kachura, and E. A. Veshkin, “Modeling the curing process of a polymer binder and changes in microhardness in its volume,” Trudy VIAM, No. 4, 07 (2021). https://doi.org/10.18577/2307-6046-2021-0-4-92-99.
M. A. Khaskov, D. A. Mel’nikov, and E.V. Kotova, “Selection of temperature and time regimes for curing epoxy binders, taking into account the scale factor,” Klei. Germetiki. Tekhnol., No. 10, 24–32 (2017).
M. A. Khaskov, “Extension of the time–temperature–transformation diagram taking into account thermal properties of components for optimizing the curing of polymer matrix composites,” Russ. J. Appl. Chem. 89, 622–630 (2016).
D. A. Mel’nikov, M. A. Khaskov, M. A. Guseva, and N. V. Antyufeeva, “On the issue of developing pressing modes for layered PCM based on prepregs,” Trudy VIAM, No. 2, 09 (2018). https://doi.org/10.18577/2307-6046-2018-0-2-9-9
G. F. Zhelezina, “Structural and functional organoplastics of a new generation,” Trydy VIAM, No, 4, o07 (2013).
G. F. Zhelezina, I. N. Gulyaev, and N. A. Solov’eva, “New generation aramid organoplastics for aircraft structures,” Aviats. Mater. Tekhnol., No. S, 368–378 (2017). https://doi.org/10.18577/2071-9140-2017-0-S-368-378
G. F. Zhelezina, S. I. Voinov, T. D. Karimbaev, and A. A. Chernyshev, “Aramid organoplastics for aircraft engine fan housings,” Vopr. Materialoved., No. 32. 153–165 (2017).
M. F. Grenier-Loustalot, M. P. Bente, and Ph. Grenier, “Reactivite du dicyandiamide vis a vis des groupements et n-epoxide-1. Mechanism reactionnel,” Eur. Polym. J. 27, 1201–1216 (1991).
Funding
This work was supported by ongoing institutional funding. No additional grants to carry out or direct this particular research were obtained.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors of this work declare that they have no conflicts of interest.
Additional information
Translated by V. Selikhanovich
Publisher’s Note.
Pleiades Publishing remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Antyufeeva, N.V., Starkov, A.I. The Influence of the Content of Halogen-Containing Oligomer in the Composition of VSK-14-6 Adhesive Binder on the Kinetics of the Curing Process of Prepregs on Different Fillers and a Comparative Analysis of the Curing Kinetics of Prepregs Based on VSK-14-1 Adhesive Binder. Polym. Sci. Ser. D 16, 882–891 (2023). https://doi.org/10.1134/S1995421223040032
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S1995421223040032