Abstract
Chemical modification is an efficient strategy for improving wood quality; however, for some fast-grown wood species unwanted shrinkage occur upon treatment with alkaline solution. This study was devised to reveal the shrinkage behavior of poplar and radiata pine woods treated with 5, 10, 15 and 20 % alkaline sodium silicate (SS) solutions. Wood treated with sodium hydroxide (SH) solution adjusting to the same pH as the specific SS solution was used as a reference sample. The weight loss, chemical components analysis, and confocal microscopy revealed that treatments with SS caused considerable reductions in hemicellulose and acid-insoluble lignin (AIL) of poplar wood up to 51 % and 21 %, respectively. In contrast, such reductions of the SS-treated radiata pine wood were only 13 % and 2 %, respectively. Consequently, shrinkage of poplar wood in the tangential- and radial-directions reached up to 22 % and 11 % respectively. However, such shrinkage for radiata pine was less than 2 % in either direction. The crystallinity index of poplar and radiata pine woods after treatment increased up to 35.3 % and 4.8 %, respectively, attributable to removal of the amorphous fraction. The scanning electron microscopy displayed that treatments had minor effect on the cell structure of radiata pine, but brought about significant collapse of poplar cells. The above results show that radiata pine is more chemically stable to alkaline treatment than poplar.
Funding source: National Key Research and Development Program of China
Award Identifier / Grant number: 2023YFD2201400
-
Research ethics: Not applicable.
-
Author contributions: The authors have accepted responsibility for the entire content of this manuscript and approved its submission.
-
Competing interests: The authors state no conflict of interest.
-
Research funding: The authors thank for the financial support from the National Key Research and Development Program of China (2023YFD2201400).
-
Data availability: Not applicable.
References
Alén, R. (2024). Chemistry for biomass utilization. Walter de Gruyter GmbH & Co KG, Berlin, Boston.10.1515/9783110608366Search in Google Scholar
Bak, M., Molnár, F., Rákosa, R., Németh, Z., and Németh, R. (2022). Dimensional stabilization of wood by microporous silica aerogel using in-situ polymerization. Wood Sci. Technol. 56: 1353–1375, https://doi.org/10.1007/s00226-022-01412-y.Search in Google Scholar
Baldacci‐Cresp, F., Spriet, C., Twyffels, L., Blervacq, A.S., Neutelings, G., Baucher, M., and Hawkins, S. (2020). A rapid and quantitative safranin‐based fluorescent microscopy method to evaluate cell wall lignification. Plant J. 102: 1074–1089, https://doi.org/10.1111/tpj.14675.Search in Google Scholar PubMed
Bao, X., Zhang, M., Li, P., Lu, J., Yuan, G., and Zuo, Y. (2023). Investigating the surface wettability and surface free energy of sodium silicate-impregnated poplar wood. Wood Mater. Sci. Eng. 18: 141–150, https://doi.org/10.1080/17480272.2021.1996454.Search in Google Scholar
Bay, M.S., Karimi, K., Esfahany, M.N., and Kumar, R. (2020). Structural modification of pine and poplar wood by alkali pretreatment to improve ethanol production. Ind. Crops Prod. 152: 112506, https://doi.org/10.1016/j.indcrop.2020.112506.Search in Google Scholar
Boyd, J. (1972). Tree growth stresses-part V: evidence of an origin in differentiation and lignification. Wood Sci. Technol. 6: 251–262, https://doi.org/10.1007/bf00357047.Search in Google Scholar
Boyd, J. (1977). Relationship between fibre morphology and shrinkage of wood. Wood Sci. Technol. 11: 3–22, https://doi.org/10.1007/bf00353597.Search in Google Scholar
Chen, G.C. (2009). Treatment of wood with polysilicic acid derived from sodium silicate for fungal decay protection. Wood Fiber Sci. 41: 220–228.Search in Google Scholar
Cheng, S., Huang, A., Wang, S., and Zhang, Q. (2016). Effect of different heat treatment temperatures on the chemical composition and structure of Chinese fir wood. BioResources 11: 4006–4016, https://doi.org/10.15376/biores.11.2.4006-4016.Search in Google Scholar
Dinand, E., Vignon, M., Chanzy, H., and Heux, L. (2002). Mercerization of primary wall cellulose and its implication for the conversion of cellulose I→ cellulose II. Cellulose 9: 7–18, https://doi.org/10.1023/a:1015877021688.10.1023/A:1015877021688Search in Google Scholar
Donaldson, L.A., Cairns, M., and Hill, S.J. (2018). Comparison of micropore distribution in cell walls of softwood and hardwood xylem. Plant Physiol. 178: 1142–1153, https://doi.org/10.1104/pp.18.00883.Search in Google Scholar PubMed PubMed Central
Dong, Y., Yan, Y., Zhang, S., Li, J., and Wang, J. (2015). Flammability and physical–mechanical properties assessment of wood treated with furfuryl alcohol and nano-SiO2. Eur. J. Wood Wood Prod. 73: 457–464, https://doi.org/10.1007/s00107-015-0896-y.Search in Google Scholar
Furuno, T., Uehara, T., and Jodai, S. (1993). Combinations of wood and silicate, 3: some properties of wood-mineral composites using the water glass-boron compound system. Mokuzai Gakkaishi. 39: 561–570.Search in Google Scholar
González-Peña, M.M., Curling, S.F., and Hale, M.D. (2009). On the effect of heat on the chemical composition and dimensions of thermally-modified wood. Polym. Degrad. Stab. 94: 2184–2193, https://doi.org/10.1016/j.polymdegradstab.2009.09.003.Search in Google Scholar
Hori, R., Suzuki, H., Kamiyama, T., and Sugiyama, J. (2003). Variation of microfibril angles and chemical composition: implication for functional properties. J. Mater. Sci. Lett. 22: 963–966, https://doi.org/10.1023/a:1024604728118.10.1023/A:1024604728118Search in Google Scholar
Howell, C., Hastrup, A.C.S., Goodell, B., and Jellison, J. (2009). Temporal changes in wood crystalline cellulose during degradation by brown rot fungi. Int. Biodeter. Biodegr. 63: 414–419.10.1016/j.ibiod.2008.11.009Search in Google Scholar
Jähn, A., Schröder, M., Füting, M., Schenzel, K., and Diepenbrock, W. (2002). Characterization of alkali treated flax fibres by means of FT Raman spectroscopy and environmental scanning electron microscopy. Spectrochim. Acta A. 58: 2271–2279, https://doi.org/10.1016/s1386-1425(01)00697-7.Search in Google Scholar PubMed
Kim, J.-y., Kim, S.-c., and Kim, B.-r. (2020). Microfibril angle characteristics of Korean pine trees from depending on provinces. J. Korean Wood Sci. Technol. 48: 569–576, https://doi.org/10.5658/wood.2020.48.4.569.Search in Google Scholar
Kita, Y. and Sugiyama, J. (2021). Wood identification of two anatomically similar Cupressaceae species based on two-dimensional microfibril angle mapping. Holzforschung 75: 591–602, https://doi.org/10.1515/hf-2020-0079.Search in Google Scholar
Kuai, B., Wang, Z., Gao, J., Tong, J., Zhan, T., Zhang, Y., Lu, J., and Cai, L. (2022). Development of densified wood with high strength and excellent dimensional stability by impregnating delignified poplar by sodium silicate. Constr. Build. Mater. 344: 128282, https://doi.org/10.1016/j.conbuildmat.2022.128282.Search in Google Scholar
Lautner, S., Zollfrank, C., and Fromm, J. (2012). Microfibril angle distribution of poplar tension wood. IAWA J. 33: 431–439, https://doi.org/10.1163/22941932-90000105.Search in Google Scholar
Lehto, J., Louhelainen, J., Kłosińska, T., Drożdżek, M., and Alén, R. (2018). Characterization of alkali-extracted wood by FTIR-ATR spectroscopy. Biomass Convers. Biorefin. 8: 847–855, https://doi.org/10.1007/s13399-018-0327-5.Search in Google Scholar
Li, L., Wang, X., and Wu, F. (2016). Chemical analysis of densification, drying, and heat treatment of Scots pine (Pinus sylvestris L.) through a hot-pressing process. BioResources 11: 3856–3874, https://doi.org/10.15376/biores.11.2.3856-3874.Search in Google Scholar
Lichtenegger, H., Reiterer, A., Stanzl-Tschegg, S., and Fratzl, P. (1999). Variation of cellulose microfibril angles in softwoods and hardwoods: a possible strategy of mechanical optimization. J. Struct. Biol. 128: 257–269, https://doi.org/10.1006/jsbi.1999.4194.Search in Google Scholar PubMed
Lionetto, F., Del Sole, R., Cannoletta, D., Vasapollo, G., and Maffezzoli, A. (2012). Monitoring wood degradation during weathering by cellulose crystallinity. Materials 5: 1910–1922, https://doi.org/10.3390/ma5101910.Search in Google Scholar
Liu, M., Zhao, Z., and Yu, W. (2020). Citric acid modified wood membranes for efficient adsorption of tetracycline: effect of alkali pretreatment concentration and adsorption mechanism. Chem. Eng. J. 393: 124748, https://doi.org/10.1016/j.cej.2020.124748.Search in Google Scholar
Liu, R., Sun, Y., Meng, F., Wang, Y., Zhai, F., and Li, Q. (2023). The effect of hemicellulose pre-extraction on the wood viscoelasticity and its implications on the fiber separation mechanism in chemi-mechanical pulping. Biomass Bioenergy 177: 106949, https://doi.org/10.1016/j.biombioe.2023.106949.Search in Google Scholar
Mai, C. and Militz, H. (2004). Modification of wood with silicon compounds. Treatment systems based on organic silicon compounds-a review. Wood Sci. Technol. 37: 453–461, https://doi.org/10.1007/s00226-004-0225-9.Search in Google Scholar
Meng, X., Wells, T., Sun, Q., Huang, F., and Ragauskas, A. (2015). Insights into the effect of dilute acid, hot water or alkaline pretreatment on the cellulose accessible surface area and the overall porosity of Populus. Green Chem. 17: 4239–4246, https://doi.org/10.1039/c5gc00689a.Search in Google Scholar
Nguyen, T.T., Xiao, Z., Che, W., Trinh, H.M., and Xie, Y. (2019). Effects of modification with a combination of styrene-acrylic copolymer dispersion and sodium silicate on the mechanical properties of wood. J. Wood Sci. 65: 1–11, https://doi.org/10.1186/s10086-019-1783-7.Search in Google Scholar
Nishiyama, Y., Sugiyama, J., Chanzy, H., and Langan, P. (2003). Crystal structure and hydrogen bonding system in cellulose Iα from synchrotron X-ray and neutron fiber diffraction. J. Am. Chem. Soc. 125: 14300–14306, https://doi.org/10.1021/ja037055w.Search in Google Scholar PubMed
Noori, M.S. and Karimi, K. (2016). Detailed study of efficient ethanol production from elmwood by alkali pretreatment. Biochem. Eng. J. 105: 197–204, https://doi.org/10.1016/j.bej.2015.09.019.Search in Google Scholar
Pereyra, A.M. and Giudice, C.A. (2009). Flame-retardant impregnants for woods based on alkaline silicates. Fire Saf. J. 44: 497–503, https://doi.org/10.1016/j.firesaf.2008.10.004.Search in Google Scholar
Rowell, R.M. (2012). Handbook of wood chemistry and wood composites. CRC Press, London, NY.10.1201/b12487Search in Google Scholar
Salehian, P., Karimi, K., Zilouei, H., and Jeihanipour, A. (2013). Improvement of biogas production from pine wood by alkali pretreatment. Fuel 106: 484–489, https://doi.org/10.1016/j.fuel.2012.12.092.Search in Google Scholar
Scheller, H.V. and Ulvskov, P. (2010). Hemicelluloses. Annu. Rev. Plant Biol. 61: 263–289, https://doi.org/10.1146/annurev-arplant-042809-112315.Search in Google Scholar PubMed
Segal, L., Creely, J., Martin, A.Jr, and Conrad, C. (1959). An empirical method for estimating the degree of crystallinity of native cellulose using the X-ray diffractometer. Text. Res. J. 29: 786–794, https://doi.org/10.1177/004051755902901003.Search in Google Scholar
Shimizu, S., Akiyama, T., Yokoyama, T., and Matsumoto, Y. (2017). Chemical factors underlying the more rapid β-O-4 bond cleavage of syringyl than guaiacyl lignin under alkaline delignification conditions. J. Wood Chem. Technol. 37: 451–466, https://doi.org/10.1080/02773813.2017.1340957.Search in Google Scholar
Slimak, K.M. and Slimak, R.A. (2007). Process of using sodium silicate to create fire retardant products, US Patent: 7.297.411 B2, United States.Search in Google Scholar
Sun, Z., Lv, J., Wang, Z., Wu, Y., Yuan, G., and Zuo, Y. (2021). Sodium silicate/waterborne epoxy resin hybrid-modified Chinese fir wood. Wood Sci. Technol. 55: 837–855, https://doi.org/10.1007/s00226-021-01287-5.Search in Google Scholar
Sweygers, N., Depuydt, D.E., Eyley, S., Thielemans, W., Mosleh, Y., Ivens, J., Dewil, R., Appels, L., and Van Vuure, A.W. (2022). Prediction of the equilibrium moisture content based on the chemical composition and crystallinity of natural fibres. Ind. Crops Prod. 186: 115187, https://doi.org/10.1016/j.indcrop.2022.115187.Search in Google Scholar
Tsuyama, T. and Takabe, K. (2014). Distribution of lignin and lignin precursors in differentiating xylem of Japanese cypress and poplar. J. Wood Sci. 60: 353–361, https://doi.org/10.1007/s10086-014-1417-z.Search in Google Scholar
Wang, P., Fu, Y., Shao, Z., Zhang, F., and Qin, M. (2016). Structural changes to aspen wood lignin during autohydrolysis pretreatment. BioResources 11: 4086–4103, https://doi.org/10.15376/biores.11.2.4086-4103.Search in Google Scholar
Weng, M., Zhu, Y., Mao, W., Zhou, J., and Xu, W. (2023). Nano-silica/urea-formaldehyde resin-modified fast-growing lumber performance study. Forests 14: 1440, https://doi.org/10.3390/f14071440.Search in Google Scholar
Winandy, J.E., Wiesner, F., Hassan, B., and Morrell, J.J. (2022). Fire performance of timber: review for use in wildland-urban interfaces. Holzforschung 76: 679–698, https://doi.org/10.1515/hf-2022-0038.Search in Google Scholar
Xiao, Z., Xu, J., Mai, C., Militz, H., Wang, Q., and Xie, Y. (2016). Combustion behavior of Scots pine (Pinus sylvestris L.) sapwood treated with a dispersion of aluminum oxychloride-modified silica. Holzforschung 70: 1165–1173, https://doi.org/10.1515/hf-2016-0062.Search in Google Scholar
Xing, L., Hu, C., Zhang, W., Guan, L., and Gu, J. (2020). Transition of cellulose supramolecular structure during concentrated acid treatment and its implication for cellulose nanocrystal yield. Carbohydr. Polym. 229: 115539, https://doi.org/10.1016/j.carbpol.2019.115539.Search in Google Scholar PubMed
Yan, Y., Dong, Y., Li, J., Zhang, S., Xia, C., Shi, S.Q., and Cai, L. (2015). Enhancement of mechanical and thermal properties of Poplar through the treatment of glyoxal-urea/nano-SiO2. RSC Adv. 5: 54148–54155, https://doi.org/10.1039/c5ra07294h.Search in Google Scholar
Yang, J., Wang, Y., Zhang, W., Li, M., Peng, F., and Bian, J. (2021). Alkaline deep eutectic solvents as novel and effective pretreatment media for hemicellulose dissociation and enzymatic hydrolysis enhancement. Int. J. Biol. Macromol. 193: 1610–1616, https://doi.org/10.1016/j.ijbiomac.2021.10.223.Search in Google Scholar PubMed
Yin, J., Yuan, T., Lu, Y., Song, K., Li, H., Zhao, G., and Yin, Y. (2017). Effect of compression combined with steam treatment on the porosity, chemical compositon and cellulose crystalline structure of wood cell walls. Carbohydr. Polym. 155: 163–172, https://doi.org/10.1016/j.carbpol.2016.08.013.Search in Google Scholar PubMed
Zhang, Y., Bi, X., Li, P., Wu, Y., Yuan, G., Li, X., and Zuo, Y. (2021). Sodium silicate/magnesium chloride compound-modified Chinese fir wood. Wood Sci. Technol. 55: 1781–1794, https://doi.org/10.1007/s00226-021-01327-0.Search in Google Scholar
Zhao, Y., He, L., Kang, J., Gao, J., Huo, G., Xu, K., Wang, T., He, Z., Wang, Z., and Yi, S. (2024). Effects of tannin acid impregnated pretreatment on dimensional stability and chemical composition of heat-treated Chinese fir. Holzforschung 77: 713–723.Search in Google Scholar
Zhou, Y., Li, P., Zhang, Y., Yuan, G., Wang, X., Wu, Y., and Zuo, Y. (2020). Process optimization of sodium silicate reinforced Chinese fir wood based on respiratory impregnation. Mater Rep 34: 18171–18176.Search in Google Scholar
Zugenmaier, P. (2001). Conformation and packing of various crystalline cellulose fibers. Prog. Polym. Sci. 26: 1341–1417, https://doi.org/10.1016/s0079-6700(01)00019-3.Search in Google Scholar
© 2024 Walter de Gruyter GmbH, Berlin/Boston
